How do I identify this component? It just says 0 on it
$begingroup$
Can anyone help me identify this component? It just says 0 or D on it (I think it's a zero). I tested it for conductivity with a multimeter - doesn't seem to have any (tried both polarities in case it's a diode). Tested for resistance: nothing (i.e. infinite resistance), although I'm not 100% sure I was touching the contact points correctly, so don't take this as an ultimate measurement. Thanks in advance!
identification components
asked 1 hour ago
Todor K.Todor K.
1061
New contributor
Todor K. is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
$endgroup$
add a comment |
$begingroup$
Can anyone help me identify this component? It just says 0 or D on it (I think it's a zero). I tested it for conductivity with a multimeter - doesn't seem to have any (tried both polarities in case it's a diode). Tested for resistance: nothing (i.e. infinite resistance), although I'm not 100% sure I was touching the contact points correctly, so don't take this as an ultimate measurement. Thanks in advance!
identification components
asked 1 hour ago
Todor K.Todor K.
1061
New contributor
Todor K. is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
$endgroup$
3
$begingroup$
That's a 0Ω resistor, a brigde in form of a chip resistor, so it can be easily placed by a machine.
$endgroup$
– Janka
1 hour ago
$begingroup$
Thanks. Well, I unsoldered it from the board and tried to test its conductivity, but there is none. I guess I could have damaged it during removal...
$endgroup$
– Todor K.
50 mins ago
add a comment |
$begingroup$
Can anyone help me identify this component? It just says 0 or D on it (I think it's a zero). I tested it for conductivity with a multimeter - doesn't seem to have any (tried both polarities in case it's a diode). Tested for resistance: nothing (i.e. infinite resistance), although I'm not 100% sure I was touching the contact points correctly, so don't take this as an ultimate measurement. Thanks in advance!
identification components
asked 1 hour ago
Todor K.Todor K.
1061
New contributor
Todor K. is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
$endgroup$
Can anyone help me identify this component? It just says 0 or D on it (I think it's a zero). I tested it for conductivity with a multimeter - doesn't seem to have any (tried both polarities in case it's a diode). Tested for resistance: nothing (i.e. infinite resistance), although I'm not 100% sure I was touching the contact points correctly, so don't take this as an ultimate measurement. Thanks in advance!
identification components
identification components
asked 1 hour ago
Todor K.Todor K.
1061
New contributor
Todor K. is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
asked 1 hour ago
Todor K.Todor K.
1061
New contributor
Todor K. is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
asked 1 hour ago
Todor K.Todor K.
1061
New contributor
Todor K. is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
asked 1 hour ago
Todor K.Todor K.
1061
asked 1 hour ago
Todor K.Todor K.
1061
1061
New contributor
Todor K. is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
New contributor
Todor K. is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
Todor K. is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
3
$begingroup$
That's a 0Ω resistor, a brigde in form of a chip resistor, so it can be easily placed by a machine.
$endgroup$
– Janka
1 hour ago
$begingroup$
Thanks. Well, I unsoldered it from the board and tried to test its conductivity, but there is none. I guess I could have damaged it during removal...
$endgroup$
– Todor K.
50 mins ago
add a comment |
3
$begingroup$
That's a 0Ω resistor, a brigde in form of a chip resistor, so it can be easily placed by a machine.
$endgroup$
– Janka
1 hour ago
$begingroup$
Thanks. Well, I unsoldered it from the board and tried to test its conductivity, but there is none. I guess I could have damaged it during removal...
$endgroup$
– Todor K.
50 mins ago
3
3
$begingroup$
That's a 0Ω resistor, a brigde in form of a chip resistor, so it can be easily placed by a machine.
$endgroup$
– Janka
1 hour ago
$begingroup$
That's a 0Ω resistor, a brigde in form of a chip resistor, so it can be easily placed by a machine.
$endgroup$
– Janka
1 hour ago
$begingroup$
Thanks. Well, I unsoldered it from the board and tried to test its conductivity, but there is none. I guess I could have damaged it during removal...
$endgroup$
– Todor K.
50 mins ago
$begingroup$
Thanks. Well, I unsoldered it from the board and tried to test its conductivity, but there is none. I guess I could have damaged it during removal...
$endgroup$
– Todor K.
50 mins ago
add a comment |
3 Answers
3
active
oldest
votes
$begingroup$
This is a 0 Ohm resistor. Probably in 0805 package.
It the multimeter shows an open circuit when measuring the element's resistance, then you can replace it with a solder blob or a piece of wire.
answered 48 mins ago
filofilo
6,32011232
$endgroup$
add a comment |
$begingroup$
That is an 0 Ohm Resistance. they also called SMD jumper resistors.
They are used as wire links to connect the traces on Surface mount boards. (same like jumper wires in through holes boards).
answered 29 mins ago
ElectronElectron
1,287313
$endgroup$
add a comment |
$begingroup$
It is an SMD resistor. As stated in the comments, the number indicates its resistance value; namely 0.
You mentioned you couldn't measure any resistance across it. Are you sure it's not coated?
answered 49 mins ago
MetricMetric
1235
$endgroup$
$begingroup$
Thanks. I removed it and tried testing for resistance/conductivity using its contact points on the underside, still the same result (no conductivity). But maybe those contact points or the "resistor" itself got damaged during removal. Anyway, it seems like everyone is pretty confident that it's a 0-ohm resistor and that's what I wanted to find out. I'll replace it with a jumper of some sort. Thanks!
$endgroup$
– Todor K.
44 mins ago
add a comment |
Your Answer
StackExchange.ifUsing("editor", function () {
return StackExchange.using("mathjaxEditing", function () {
StackExchange.MarkdownEditor.creationCallbacks.add(function (editor, postfix) {
StackExchange.mathjaxEditing.prepareWmdForMathJax(editor, postfix, [["\$", "\$"]]);
});
});
}, "mathjax-editing");
StackExchange.ifUsing("editor", function () {
return StackExchange.using("schematics", function () {
StackExchange.schematics.init();
});
}, "cicuitlab");
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "135"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
Todor K. is a new contributor. Be nice, and check out our Code of Conduct.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f417930%2fhow-do-i-identify-this-component-it-just-says-0-on-it%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
3 Answers
3
active
oldest
votes
3 Answers
3
active
oldest
votes
active
oldest
votes
active
oldest
votes
$begingroup$
This is a 0 Ohm resistor. Probably in 0805 package.
It the multimeter shows an open circuit when measuring the element's resistance, then you can replace it with a solder blob or a piece of wire.
answered 48 mins ago
filofilo
6,32011232
$endgroup$
add a comment |
$begingroup$
This is a 0 Ohm resistor. Probably in 0805 package.
It the multimeter shows an open circuit when measuring the element's resistance, then you can replace it with a solder blob or a piece of wire.
answered 48 mins ago
filofilo
6,32011232
$endgroup$
add a comment |
$begingroup$
This is a 0 Ohm resistor. Probably in 0805 package.
It the multimeter shows an open circuit when measuring the element's resistance, then you can replace it with a solder blob or a piece of wire.
answered 48 mins ago
filofilo
6,32011232
$endgroup$
This is a 0 Ohm resistor. Probably in 0805 package.
It the multimeter shows an open circuit when measuring the element's resistance, then you can replace it with a solder blob or a piece of wire.
answered 48 mins ago
filofilo
6,32011232
answered 48 mins ago
filofilo
6,32011232
answered 48 mins ago
filofilo
6,32011232
answered 48 mins ago
filofilo
6,32011232
6,32011232
add a comment |
add a comment |
$begingroup$
That is an 0 Ohm Resistance. they also called SMD jumper resistors.
They are used as wire links to connect the traces on Surface mount boards. (same like jumper wires in through holes boards).
answered 29 mins ago
ElectronElectron
1,287313
$endgroup$
add a comment |
$begingroup$
That is an 0 Ohm Resistance. they also called SMD jumper resistors.
They are used as wire links to connect the traces on Surface mount boards. (same like jumper wires in through holes boards).
answered 29 mins ago
ElectronElectron
1,287313
$endgroup$
add a comment |
$begingroup$
That is an 0 Ohm Resistance. they also called SMD jumper resistors.
They are used as wire links to connect the traces on Surface mount boards. (same like jumper wires in through holes boards).
answered 29 mins ago
ElectronElectron
1,287313
$endgroup$
That is an 0 Ohm Resistance. they also called SMD jumper resistors.
They are used as wire links to connect the traces on Surface mount boards. (same like jumper wires in through holes boards).
answered 29 mins ago
ElectronElectron
1,287313
answered 29 mins ago
ElectronElectron
1,287313
answered 29 mins ago
ElectronElectron
1,287313
answered 29 mins ago
ElectronElectron
1,287313
1,287313
add a comment |
add a comment |
$begingroup$
It is an SMD resistor. As stated in the comments, the number indicates its resistance value; namely 0.
You mentioned you couldn't measure any resistance across it. Are you sure it's not coated?
answered 49 mins ago
MetricMetric
1235
$endgroup$
$begingroup$
Thanks. I removed it and tried testing for resistance/conductivity using its contact points on the underside, still the same result (no conductivity). But maybe those contact points or the "resistor" itself got damaged during removal. Anyway, it seems like everyone is pretty confident that it's a 0-ohm resistor and that's what I wanted to find out. I'll replace it with a jumper of some sort. Thanks!
$endgroup$
– Todor K.
44 mins ago
add a comment |
$begingroup$
It is an SMD resistor. As stated in the comments, the number indicates its resistance value; namely 0.
You mentioned you couldn't measure any resistance across it. Are you sure it's not coated?
answered 49 mins ago
MetricMetric
1235
$endgroup$
$begingroup$
Thanks. I removed it and tried testing for resistance/conductivity using its contact points on the underside, still the same result (no conductivity). But maybe those contact points or the "resistor" itself got damaged during removal. Anyway, it seems like everyone is pretty confident that it's a 0-ohm resistor and that's what I wanted to find out. I'll replace it with a jumper of some sort. Thanks!
$endgroup$
– Todor K.
44 mins ago
add a comment |
$begingroup$
It is an SMD resistor. As stated in the comments, the number indicates its resistance value; namely 0.
You mentioned you couldn't measure any resistance across it. Are you sure it's not coated?
answered 49 mins ago
MetricMetric
1235
$endgroup$
It is an SMD resistor. As stated in the comments, the number indicates its resistance value; namely 0.
You mentioned you couldn't measure any resistance across it. Are you sure it's not coated?
answered 49 mins ago
MetricMetric
1235
answered 49 mins ago
MetricMetric
1235
answered 49 mins ago
MetricMetric
1235
answered 49 mins ago
MetricMetric
1235
1235
$begingroup$
Thanks. I removed it and tried testing for resistance/conductivity using its contact points on the underside, still the same result (no conductivity). But maybe those contact points or the "resistor" itself got damaged during removal. Anyway, it seems like everyone is pretty confident that it's a 0-ohm resistor and that's what I wanted to find out. I'll replace it with a jumper of some sort. Thanks!
$endgroup$
– Todor K.
44 mins ago
add a comment |
$begingroup$
Thanks. I removed it and tried testing for resistance/conductivity using its contact points on the underside, still the same result (no conductivity). But maybe those contact points or the "resistor" itself got damaged during removal. Anyway, it seems like everyone is pretty confident that it's a 0-ohm resistor and that's what I wanted to find out. I'll replace it with a jumper of some sort. Thanks!
$endgroup$
– Todor K.
44 mins ago
$begingroup$
Thanks. I removed it and tried testing for resistance/conductivity using its contact points on the underside, still the same result (no conductivity). But maybe those contact points or the "resistor" itself got damaged during removal. Anyway, it seems like everyone is pretty confident that it's a 0-ohm resistor and that's what I wanted to find out. I'll replace it with a jumper of some sort. Thanks!
$endgroup$
– Todor K.
44 mins ago
$begingroup$
Thanks. I removed it and tried testing for resistance/conductivity using its contact points on the underside, still the same result (no conductivity). But maybe those contact points or the "resistor" itself got damaged during removal. Anyway, it seems like everyone is pretty confident that it's a 0-ohm resistor and that's what I wanted to find out. I'll replace it with a jumper of some sort. Thanks!
$endgroup$
– Todor K.
44 mins ago
add a comment |
Todor K. is a new contributor. Be nice, and check out our Code of Conduct.
Todor K. is a new contributor. Be nice, and check out our Code of Conduct.
Todor K. is a new contributor. Be nice, and check out our Code of Conduct.
Todor K. is a new contributor. Be nice, and check out our Code of Conduct.
Thanks for contributing an answer to Electrical Engineering Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
Use MathJax to format equations. MathJax reference.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f417930%2fhow-do-i-identify-this-component-it-just-says-0-on-it%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
3
$begingroup$
That's a 0Ω resistor, a brigde in form of a chip resistor, so it can be easily placed by a machine.
$endgroup$
– Janka
1 hour ago
$begingroup$
Thanks. Well, I unsoldered it from the board and tried to test its conductivity, but there is none. I guess I could have damaged it during removal...
$endgroup$
– Todor K.
50 mins ago